![]() If the above option does not help, try to flash the device on another computer, because There are problems that do not allow you to correctly determine the memory on a particular machineĮrror description 3013 and solution It's possible that the check mark for the Uboot checkbox is not checked in the flash tool's settings. As versions of different versions are updated, information about flash memory. Check the cable, reconnect the cable to another USB portĮrror description 3012 and solution The problem is related to the definition of flash memory device. After that, connect the device through the test point, but already with the batteryĮrror description 2035 and solution After click Download connect to the computer an off device with pressed volume buttonsĮrror description 3001 and solution Perhaps the error is connected to the connection. You can try flashing the device with the battery offĮrror description 2020 and solution In the Flash Tool settings, forcibly check the box, indicating that the device is without a battery. If you select ReadBack, Format or MemoryTest, you need to connect the device in BOOTROM mode. If you need to flash these blocks, connect the phone in BOOTROM mode. If you select Download mode, a check mark is installed on the PRELOADER or DSP_BL units, you must remove it from these blocks. You must use a suitable version of the Flash Tool, for example v2.xxx for MT6573 phones, or disable DA Download All mode. If the above methods do not help, after the error appears, you must immediately close the window with an error and immediately click the button downloadĮrror description 2005 and solution An error can occur on MTD devices if the check box is not checked on the PRELOADER or DSP_BL blocks when selecting the Download mode. Can help connect the device with the volume key held down + or. Use the program USBDeview To remove installed USB drivers and perform firmware via Flash Tool. An error may occur if the operating system has a lot of USB drivers for different devices. ![]() ![]() Download the version at the end of which there is the designation SEC. Go to the folder with the firmware and delete the file Checksum.iniĮrror description 2004 and solution The problem may be version of the SP FLASH TOOL. For example, the file name contains the version number 6777, and the device version 6555Įrror description 1041 and solution You must go to the tab Help, click Open Logs Folder And delete all the logs. Can help change the version of the flash driver, or flashing the device with the battery offĮrror description 1018 and solution Use a more recent version of the driverĮrror description 1022 and solution Use a more recent version of the driverĮrror description 1040 and solution Scatter file is not suitable for the device. Solutions should be sought on the same principle. Replace the version of the driver usedĮrror description 1012 and solution Use a more recent version of the driverĮrror description 1013 and solution Error similar to error 1003. This error sometimes occurs on undeveloped versions of the Flash Tool. This is usually a kernel or recovery block. If the program has moved into such an undefined state, then you need to close it and restart itĮrror description 1011 and solution Occurs in the event that the size of one of the parts of the firmware exceeds the size of the space allocated to it. In this state, the Flash Tool does not close the COM port, and trying to restart any operation by reconnecting the device will cause an error. When after the red strip pass to 100% as a result of the firmware, Operation buttons are again available for clicking, but no error message, no green circle, this error appears, or similar to it, the code of which is 1013. The port was visible, it was selected in the Flash Tool settings, the program recorded it in the INI file, after which the system was rebooted with the port disabled, and immediately launched the Flash Tool without selecting the port. Theoretically, it can occur in the USB UART mode. If the USB port of the computer is faulty, then it is necessary to puncture the cable to another port. The problem can be in the USB cable, in this case, replace the cable. In this case, you will not see the equipment on which the PRELOADER drivers are placed. Even if the COM port is virtual, and the physical USB. ![]() For example, an error may occur if COM ports are disabled in the BIOS. ![]() For example, in the scatter file, the PRELOADER and DSP_BL blocks are disabledĮrror description 1003 and solution The problem with the port. Error description 1002 and solution Incorrect Scatter file. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |